New hardware in kernel.log

General discussion and feedback on development topics

New hardware in kernel.log

Postby MadRocker » Thu Feb 17, 2011 5:25 am

Can some one confirm if this is useful, kernel config arm6k = yes and android mem early start = yes works fine. The touchscreen calibration we might be able to set it in the .c file somehow and ignore the cmd line / ignore the append-jet as this below seems to override append-jet.

Code: Select all
[    3.005856] S3C NAND Driver, (c) 2008 Samsung Electronics
<6>[    3.017526] NAND device: Manufacturer ID: 0x98, Chip ID: 0x39 (Toshiba NAND 8MiB 1,8V 8-bit)
<4>[    3.037006] flash size: 8 MiB
<4>[    3.046702] page size: 512 bytes
<4>[    3.056285] OOB area size: 16 bytes
<4>[    3.065827] sector size: 8 KiB
<4>[    3.075342] pages number: 16384
<4>[    3.084723] pages per sector: 16
<4>[    3.093978] bus width: 8
<4>[    3.103153] bits in sector size: 13
<4>[    3.112283] bits in page size: 9
<4>[    3.121296] bits in OOB size: 4
<4>[    3.130186] flash size with OOB: 8448 KiB
<4>[    3.139060] page address bytes: 3
<4>[    3.147787] sector address bytes: 2
<4>[    3.156451] options: 0x62
<6>[    3.166007] Scanning device for bad blocks
<5>[    3.188503] Creating 1 MTD partitions on "NAND 8MiB 1,8V 8-bit":


Code: Select all
<6>[    4.006680] input: s3c-keypad-rev0000 as /devices/virtual/input/input0
<4>[    4.026070] s3c-keypad Initialized (columns=3 rows=4)
<6>[    4.036043] S3C Keypad Driver
<6>[    4.045363] S3C Touchscreen driver, (c) 2008 Samsung Electronics
<6>[    4.063424] S3C TouchScreen: delay=30000 oversampling=3
<6>[    4.072739] S3C TouchScreen: calibration: xmin=0 xmax=4095 ymin=0 ymax=4095
<6>[    4.090719] s3c_ts.c: TS_IRQ registered (94)
<6>[    4.099867] s3c_ts.c: ADC_IRQ registered (95)
<6>[    4.108903] S3C TouchScreen got loaded successfully : 12 bits

I/KeyInputQueue( 2251): Device added: id=0x0, name=s3c-keypad-rev0000, classes=1
I/KeyInputQueue( 2251): Device added: id=0x10001, name=S3C TouchScreen, classes=4
I/KeyInputQueue( 2251):   X: min=0 max=4095 flat=0 fuzz=0
I/KeyInputQueue( 2251):   Y: min=0 max=4095 flat=0 fuzz=0
I/KeyInputQueue( 2251):   Pressure: min=0 max=1 flat=0 fuzz=0
I/KeyInputQueue( 2251):   Size: unknown values
I/KeyInputQueue( 2251): No virtual keys found
I/KeyInputQueue( 2251): Ignoring non-input device: id=0x10000, name=kxsd9


Code: Select all
<6>[    4.779993] s3c_bat_init
<6>[    4.788549] instinctq-battery instinctq-battery: s3c_bat_probe
<7>[    4.804717] power_supply battery: uevent
<7>[    4.804745] power_supply battery: No power supply yet
<7>[    4.805506] power_supply battery: power_supply_changed
<7>[    4.805693] power_supply usb: uevent
<7>[    4.805714] power_supply usb: No power supply yet
<7>[    4.805803] power_supply battery: power_supply_changed_work
<7>[    4.805838] power_supply battery: s3c_bat_get_property : psp = 0
<7>[    4.805861] instinctq-battery instinctq-battery: s3c_bat_get_charging_status : Not Charging
<7>[    4.805883] power_supply battery: power_supply_update_bat_leds 3
<7>[    4.805950] power_supply battery: uevent
<7>[    4.805969] power_supply battery: POWER_SUPPLY_NAME=battery
<7>[    4.806017] power_supply battery: Static prop TYPE=Battery
<7>[    4.806040] power_supply battery: 5 dynamic props
<7>[    4.806057] power_supply battery: s3c_bat_get_property : psp = 0
<7>[    4.806075] instinctq-battery instinctq-battery: s3c_bat_get_charging_status : Not Charging
<7>[    4.806098] power_supply battery: prop STATUS=Not charging
<7>[    4.806116] power_supply battery: s3c_bat_get_property : psp = 1
<7>[    4.806136] power_supply battery: prop HEALTH=Good
<7>[    4.806153] power_supply battery: s3c_bat_get_property : psp = 2
<7>[    4.806170] power_supply battery: prop PRESENT=1
<7>[    4.806186] power_supply battery: s3c_bat_get_property : psp = 4
<7>[    4.806204] power_supply battery: prop TECHNOLOGY=Li-ion
<7>[    4.806221] power_supply battery: s3c_bat_get_property : psp = 26
<7>[    4.806238] instinctq-battery instinctq-battery: s3c_bat_get_property : level = 0
<7>[    4.806257] power_supply battery: prop CAPACITY=0
<7>[    4.806805] power_supply usb: power_supply_changed
<7>[    4.806979] power_supply ac: uevent
<7>[    4.807000] power_supply ac: No power supply yet
<7>[    4.807371] power_supply usb: power_supply_changed_work
<7>[    4.807411] power_supply usb: s3c_power_get_property : psp = 3
<7>[    4.807432] power_supply usb: power_supply_update_gen_leds 0
<7>[    4.807482] power_supply usb: uevent
<7>[    4.807496] power_supply usb: POWER_SUPPLY_NAME=usb
<7>[    4.807540] power_supply usb: Static prop TYPE=USB
<7>[    4.807559] power_supply usb: 1 dynamic props
<7>[    4.807576] power_supply usb: s3c_power_get_property : psp = 3
<7>[    4.807594] power_supply usb: prop ONLINE=0
<7>[    4.808041] power_supply ac: power_supply_changed
<7>[    4.808142] instinctq-battery instinctq-battery: s3c_bat_status_update ++
<7>[    4.808167] power_supply battery: power_supply_changed
<7>[    4.808187] instinctq-battery instinctq-battery: s3c_bat_status_update : call power_supply_changed
<7>[    4.808210] instinctq-battery instinctq-battery: s3c_bat_status_update --
<7>[    4.808670] power_supply ac: power_supply_changed_work
<7>[    4.808713] power_supply ac: s3c_power_get_property : psp = 3
<7>[    4.808730] power_supply ac: power_supply_update_gen_leds 0
<7>[    4.808784] power_supply ac: uevent
<7>[    4.808798] power_supply ac: POWER_SUPPLY_NAME=ac
<7>[    4.808839] power_supply ac: Static prop TYPE=Mains
<7>[    4.808859] power_supply ac: 1 dynamic props
<7>[    4.808874] power_supply ac: s3c_power_get_property : psp = 3
<7>[    4.808893] power_supply ac: prop ONLINE=0
<7>[    4.809807] power_supply battery: power_supply_changed_work
<7>[    4.809846] power_supply battery: s3c_bat_get_property : psp = 0
<7>[    4.809868] instinctq-battery instinctq-battery: s3c_bat_get_charging_status : Not Charging
<7>[    4.809889] power_supply battery: power_supply_update_bat_leds 3
<7>[    4.809943] power_supply battery: uevent
<7>[    4.809958] power_supply battery: POWER_SUPPLY_NAME=battery
<7>[    4.810001] power_supply battery: Static prop TYPE=Battery
<7>[    4.810113] power_supply battery: 5 dynamic props
<7>[    4.810139] power_supply battery: s3c_bat_get_property : psp = 0
<7>[    4.810159] instinctq-battery instinctq-battery: s3c_bat_get_charging_status : Not Charging
<7>[    4.810185] power_supply battery: prop STATUS=Not charging
<7>[    4.810206] power_supply battery: s3c_bat_get_property : psp = 1
<7>[    4.810225] power_supply battery: prop HEALTH=Good
<7>[    4.810241] power_supply battery: s3c_bat_get_property : psp = 2
<7>[    4.810259] power_supply battery: prop PRESENT=1
<7>[    4.810275] power_supply battery: s3c_bat_get_property : psp = 4
<7>[    4.810293] power_supply battery: prop TECHNOLOGY=Li-ion
<7>[    4.810309] power_supply battery: s3c_bat_get_property : psp = 26
<7>[    4.810327] instinctq-battery instinctq-battery: s3c_bat_get_property : level = 80
<7>[    4.810346] power_supply battery: prop CAPACITY=80
MadRocker
Dev Team
Dev Team
 
Posts: 528
Joined: Sun Dec 12, 2010 7:15 am

Advertisement

       

Re: New hardware in kernel.log

Postby Dopi » Sat Feb 19, 2011 10:39 am

MadRocker wrote:Can some one confirm if this is useful, kernel config arm6k = yes and android mem early start = yes works fine. The touchscreen calibration we might be able to set it in the .c file somehow and ignore the cmd line / ignore the append-jet as this below seems to override append-jet.

I have not tested the arm6k option. Did you see any noticable difference to kernels without this option?

I already fixed the calibration in my experimental-2.6.29.dopi kernel branch. It must habe been lost when applying some other patches. Now it is back in and /boot/append-jet should not be needed anymore.

Cheers,
Dopi
Ad banners support the JetDroid forum. Please consider clicking them once in a while.
User avatar
Dopi
Dev Team
Dev Team
 
Posts: 926
Joined: Sun Aug 22, 2010 9:47 pm


Return to Development Discussion / Feedback

Who is online

Users browsing this forum: No registered users and 1 guest

  • Advertisement
cron